General

general-4

Exit

Question 1 of 1

Time Left

587849

block

The correct way to connect a test voltmeter is:

Select the correct answer(s).

(0/0)

587851

none

The control valve switch must be placed in the neutral position when the landing gears are down to:

Select the correct answer(s).

(0/0)

587853

none

what type of weld is shown at G?

Select the correct answer(s).

(0/0)

587854

none

A lead-acid battery with 12 cells connected in a series (no-load voltage = 2.1 volts per cell) furnishes 10 amperes to a load of 2 ohms resistance. Th internal resistance of the battery in this instance is:

Select the correct answer(s).

(0/0)

587855

none

A circuit has an applied voltage of 30 volts and a load consisting of a 10-ohm resistor in series with a 20 ohm resistor. What is the voltage drop across the 10-ohm resistor?

Select the correct answer(s).

(0/0)

587858

none

What is the allowable manufacturing tolerance for a bushing where the outside dimensions shown on the blueprint are: 1.0625+.0025-.0003?

Select the correct answer(s).

(0/0)

587860

none

(1) Measurement should not be scaled from an aircraft print because the paper shrinks or stretches when the print is made. (2) When a detail drawing is made, it is carefully and accurately drawn to scale, and is dimensioned. Regarding the above statements:

Select the correct answer(s).

(0/0)

587862

none

Which requires the most electrical power? 1 Horsepower = 746 watts

Select the correct answer(s).

(0/0)

587863

none

If resistor R5 is disconnected at the junction of R4 and R3 as shown, what will the ohmmeter read?

Select the correct answer(s).

(0/0)

587864

none

The measurement reading on the micrometer is

Select the correct answer(s).

(0/0)

587865

none

Which tool is used to find the center of a shaft or other cylindrical work?

Select the correct answer(s).

(0/0)

587876

none

Which of the following hose materials are compatible with phosphate-ester base hydraulic fluids? 1. BUTYL 2. TEFLON 3. BUNA-N 4. NEOPRENE

Select the correct answer(s).

(0/0)

587877

none

A part which is being prepared for dye penetrant inspection should be cleaned with:

Select the correct answer(s).

(0/0)

587881

none

The emptied weight of an airplane is determined by:

Select the correct answer(s).

(0/0)

587895

none

General

Question 1 of 1

Time Left

The correct way to connect a test voltmeter is:

Select the correct answer(s).

(0/0)

The control valve switch must be placed in the neutral position when the landing gears are down to:

Select the correct answer(s).

(0/0)

what type of weld is shown at G?

Select the correct answer(s).

(0/0)

A lead-acid battery with 12 cells connected in a series (no-load voltage = 2.1 volts per cell) furnishes 10 amperes to a load of 2 ohms resistance. Th internal resistance of the battery in this instance is:

Select the correct answer(s).

(0/0)

A circuit has an applied voltage of 30 volts and a load consisting of a 10-ohm resistor in series with a 20 ohm resistor. What is the voltage drop across the 10-ohm resistor?

Select the correct answer(s).

(0/0)

What is the allowable manufacturing tolerance for a bushing where the outside dimensions shown on the blueprint are: 1.0625+.0025-.0003?

Select the correct answer(s).

(0/0)

(1) Measurement should not be scaled from an aircraft print because the paper shrinks or stretches when the print is made. (2) When a detail drawing is made, it is carefully and accurately drawn to scale, and is dimensioned. Regarding the above statements:

Select the correct answer(s).

(0/0)

Which requires the most electrical power? 1 Horsepower = 746 watts

Select the correct answer(s).

(0/0)

If resistor R5 is disconnected at the junction of R4 and R3 as shown, what will the ohmmeter read?

Select the correct answer(s).

(0/0)

The measurement reading on the micrometer is

Select the correct answer(s).

(0/0)

Which tool is used to find the center of a shaft or other cylindrical work?

Select the correct answer(s).

(0/0)

Which of the following hose materials are compatible with phosphate-ester base hydraulic fluids? 1. BUTYL 2. TEFLON 3. BUNA-N 4. NEOPRENE

Select the correct answer(s).

(0/0)

A part which is being prepared for dye penetrant inspection should be cleaned with:

Select the correct answer(s).

(0/0)

The emptied weight of an airplane is determined by:

Select the correct answer(s).

(0/0)

If an open occurs at R1, the light:

Select the correct answer(s).

(0/0)

Results

Correct

0

Incorrect

0

Skipped

0

Overall Percentage

0%

Rate Quiz