ASNT UTII

asnt-utii

Exit

Question 1 of 1

Time Left

94040

120

block

The process of adjusting an instrument to a reference standard is referred to as:

Select the correct answer(s).

(0/0)

94041

120

none

Which of the following is a reference reflector that is notdependent on beam angle?

Select the correct answer(s).

(0/0)

94042

120

none

A primary purpose of a reference standard is:

Select the correct answer(s).

(0/0)

94043

120

none

A set of standard reference blocks has the same overall dimensions. The only difference is the size of the flat-bottom hole reflectors. This is called a set of:

Select the correct answer(s).

(0/0)

94044

120

none

The vertical linear range of a test instrument may be determined by obtaining an ultrasonic response from:

Select the correct answer(s).

(0/0)

94045

120

none

Transducer A is being used to establish:

Select the correct answer(s).

(0/0)

94046

120

none

Transducer B is being used to check:

Select the correct answer(s).

(0/0)

94047

120

none

Transducer C is being used to check:

Select the correct answer(s).

(0/0)

94048

120

none

Transducer A is being used to check:

Select the correct answer(s).

(0/0)

94049

120

none

Transducer B is being used to check:

Select the correct answer(s).

(0/0)

94050

120

none

Which of the following is typically the acceptable range for the actual wedge angle to be compared to its nominal angle?

Select the correct answer(s).

(0/0)

94051

120

none

Significant errors in ultrasonic thickness measurement can occur if:

Select the correct answer(s).

(0/0)

94052

120

none

Instrument vertical linearity can be affected by several factors. Which of the following is not a factor for vertical linearity?

Select the correct answer(s).

(0/0)

94054

120

none

When the screen range is set up to be 10 in. (254 mm) and the transducer faces the 4 in. (101.6 mm) arc of the IIW-type calibration block, the second signal will show up on which of the following locations on the screen?

Select the correct answer(s).

(0/0)

94055

120

none

ASNT UTII

Question 1 of 1

Time Left

The process of adjusting an instrument to a reference standard is referred to as:

Select the correct answer(s).

(0/0)

Which of the following is a reference reflector that is notdependent on beam angle?

Select the correct answer(s).

(0/0)

A primary purpose of a reference standard is:

Select the correct answer(s).

(0/0)

A set of standard reference blocks has the same overall dimensions. The only difference is the size of the flat-bottom hole reflectors. This is called a set of:

Select the correct answer(s).

(0/0)

The vertical linear range of a test instrument may be determined by obtaining an ultrasonic response from:

Select the correct answer(s).

(0/0)

Transducer A is being used to establish:

Select the correct answer(s).

(0/0)

Transducer B is being used to check:

Select the correct answer(s).

(0/0)

Transducer C is being used to check:

Select the correct answer(s).

(0/0)

Transducer A is being used to check:

Select the correct answer(s).

(0/0)

Transducer B is being used to check:

Select the correct answer(s).

(0/0)

Which of the following is typically the acceptable range for the actual wedge angle to be compared to its nominal angle?

Select the correct answer(s).

(0/0)

Significant errors in ultrasonic thickness measurement can occur if:

Select the correct answer(s).

(0/0)

Instrument vertical linearity can be affected by several factors. Which of the following is not a factor for vertical linearity?

Select the correct answer(s).

(0/0)

When the screen range is set up to be 10 in. (254 mm) and the transducer faces the 4 in. (101.6 mm) arc of the IIW-type calibration block, the second signal will show up on which of the following locations on the screen?

Select the correct answer(s).

(0/0)

Compensation for the variation in echo height related to variations in discontinuity depth in the test material is known as:

Select the correct answer(s).

(0/0)

Results

Correct

0

Incorrect

0

Skipped

0

Overall Percentage

0%

Rate Quiz